Mechanical Service Technician IM (On Shift)

G

Gerresheimer

Mechanical Service Technician IM (On Shift)

Peachtree City, GA
Full Time
Paid
  • Responsibilities

    Job Description

    All of the below are part of the responsibilities of this position as needed:

    MECHANICAL AND ELECTROMECHANICAL EQUIPMENT

    • Repair/replace brakes & clutches, gears, belts, sheaves/pulley, chains and sprockets, cams, seals and o-rings, bearings and bushings. Replace couplings and valves (cut-off, pressure relief, etc)
    • Troubleshoot/repair/replace, gears, cams, seals, o-rings, bearings, bushings, shafts and motors
    • Troubleshoot/maintain chains and sprockets. Perform basic alignment
    • Maintain couplings and fans
    • Install/maintain valves (cut-off, pressure relief, etc)

    PNEUMATIC/HYDRAULIC EQUIPMENT

    • Troubleshoot/repair/replace cylinders and pneumatic/hydraulic motors
    • Maintain hydraulic systems, pumps and valves
    • Repair/replace pneumatic/hydraulic lines, hoses, and solenoids
    • Repair/replace flow controls (pneumatic or hydraulic)
    • Troubleshoot/maintain air compressors

    CONVEYING SYSTEMS

    • Troubleshoot/repair/replace/maintain vibratory, linear motion, and material conveying systems. Repair/replace belt conveyor systems

    PUMPS SYSTEMS AND MECHANICAL EQUIPMENT

    • Troubleshoot/maintain centrifugal, vacuum, gear, diaphragm, positive displacement and metering pumps
    • Perform alignment
    • Maintain heat exchanger and pipe insulation systems

    MECHANICAL OPERATIONS

    • Perform welding and fabrication tasks, sheet metal fabrication, pipefitting duties and rigging tasks
    • Perform basic math operations
    • Operate common hand and power tools, use measuring devices and precision devices

    ELECTRICAL, POWER DISTRIBUTION AND ELECTROMECHANICAL SYSTEMS

    • Apply knowledge of AC theory and run wire and conduit
    • Install/repair basic AC and DC controls, building electrical systems
    • Operate electrical test equipment
    • Fabricate/retrofit electrical control panels
    • Repair ground fault detection systems
    • Repair/replace low voltage transformers <480 and replace fuses and breakers (<600 V)
    • Repair/replace AC motors, starters and relays
    • Maintain ground fault detection system

    MACHINE AND PROCESS CONTROLS

    • Modify ladder logic and edit PLC software
    • Troubleshoot/replace/install circuit boards
    • Install/maintain/troubleshoot photo eyes and basic VFD drives (Variable Frequency Drive)
    • Install/maintain/troubleshoot limit and proximity switches & bar code readers
    • Calibrate/install/repair basic flow and density, temperature, pressure transmitters, gages and switches
    • Calibrate proportional control valves and process control loop (PID)
    • Install/calibrate load cells
    • Troubleshoot/replace transducers
    • Align and replace photo eyes
    • Install load cells
    • Repair/replace VFD drives (Variable Frequency Drive), limit and proximity switches
    • Repair flow, pressure, and speed transmitters, gages and switches

    AUTOMATION

    • Troubleshoot/repair/replace/maintain robots
    • Design/FAB/troubleshoot end of arm tooling
    • Program pick/place points.
  • Qualifications

    Qualifications

    Education Requirements:

    • High School Diploma
    • Requires a minimum of 2 years maintenance/technical experience within an plastic injection molding facility
    • Requires a minimum of 1 year mechanical/electrical experience.
    • Requires a minimum of 2 years general preventative maintenance experience in medical injection molding industry

    Experience Requirements:

    • Experienced knowledge of Good Manufacturing Practice within the Medical or Food Industry.
    • Experience working in a fast paced operational environment with constant interaction with operators, technicians and equipment
    • Experience in problem solving and troubleshooting of processes and process equipment
    • Prior diagnostic/troubleshooting and preventative experience preferred
    • Ability to read blue prints, manufacturer's specifications and schematics

    Additional Information

    • Must have good interpersonal skills with the ability to interface constructively and cooperatively with a wide variety of departmental staff and intra-department personnel.
    • Attention to detail and accuracy.
    • Ability to work well within a team environment and capable of completing projects with minimal supervision.
    • Excellent verbal communication skills
    • Required to speak, read and write English language
    • Good organizational and planning skills
    • Required to supply hand tools